Skip to content

Actions: Duet3D/RepRapFirmware

Actions

All workflows

Actions

Loading...
Loading

Showing runs from all workflows
182 workflow runs
182 workflow runs

Filter by Event

Filter by Status

Filter by Branch

Filter by Actor

M581 does not throw an error in SBC mode when incorrect P parameter is used Auto-close blank templates #225: Issue #1022 opened by T3P3
July 2, 2024 14:03 12s
July 2, 2024 14:03 12s
Parsing error when using ternary operator Auto-close blank templates #224: Issue #1021 opened by dc42
July 2, 2024 13:21 15s
July 2, 2024 13:21 15s
Incorrect processing of # operator when operand is an element of an array of arrays Auto-close blank templates #223: Issue #1020 opened by dc42
July 2, 2024 13:07 12s
July 2, 2024 13:07 12s
Main board used as expansion board doesn't handle idle current percent Auto-close blank templates #222: Issue #1019 opened by dc42
July 1, 2024 08:36 13s
July 1, 2024 08:36 13s
[Bug]: RRF 3.5.2 - LED strips connected to io ports on SAMC21 (1LC, 1XD) set LEDs incorrectly, all white Auto-close blank templates #221: Issue #1018 opened by droftarts
June 25, 2024 16:28 18s
June 25, 2024 16:28 18s
[Bug]: I erased the firmware by shorting the erase pins I installed driver files again from https://github.com/Duet3D/RepRapFirmware/blob/dev/Driver/WindowsDriverFiles.zip. I got the usual message after updating the USB driver with yellow triangle (right click, installed from the unzipped download (folder name WindowsDriverFiles) and it responded with "Unknown USB Device (Device Descriptor Request Failed). I have used the same USB cable that was working with YAT before I erased the DUet3 board. I use a powered USB hub. I see the little diag LED faintly lit, solid on, the bright red LED between USB socket and SD card and the green and red LEDs in the corner of the board on solid. Auto-close blank templates #220: Issue #1017 opened by jtreg
June 22, 2024 20:55 11s
June 22, 2024 20:55 11s
[FeatureRequest]: Forward Run / Reverse Run support for Spindles in M950 Auto-close blank templates #219: Issue #1016 opened by benagricola
June 18, 2024 10:19 13s
June 18, 2024 10:19 13s
Input shaping on linear delta causes Z motor clunking at specific bed locations Auto-close blank templates #218: Issue #1015 opened by droftarts
June 14, 2024 10:59 13s
June 14, 2024 10:59 13s
3.5.2 Upload release assets #13: Release 3.5.2 released by dc42
June 12, 2024 07:19 1m 0s
June 12, 2024 07:19 1m 0s
Build and and deploy firmware to dev Build and and deploy firmware to dev #29: Manually run by chrishamm
June 11, 2024 16:57 14m 9s v3-chrishamm
v3-chrishamm
June 11, 2024 16:57 14m 9s
Build and and deploy firmware to dev Build and and deploy firmware to dev #28: Manually run by chrishamm
June 11, 2024 16:39 4m 34s 3.5-dev
3.5-dev
June 11, 2024 16:39 4m 34s
Simple filament presence switch on mainboard with extruder on expansion board: pin not allocated correctly Auto-close blank templates #217: Issue #1014 opened by T3P3
June 10, 2024 20:38 14s
June 10, 2024 20:38 14s
3.5.2 release candidate 1 Upload release assets #12: Release 3.5.2-rc.1 published by dc42
May 31, 2024 08:13 29s
May 31, 2024 08:13 29s
Check for sufficient free memory before allocating a new heap block Auto-close blank templates #216: Issue #1013 opened by dc42
May 28, 2024 08:21 13s
May 28, 2024 08:21 13s
In SBC mode the supported nesting of function calls is too low Auto-close blank templates #215: Issue #1012 opened by dc42
May 24, 2024 08:22 12s
May 24, 2024 08:22 12s
[FeatureRequest] Add M303 cancelling to M108 Auto-close blank templates #214: Issue #1010 opened by droftarts
May 17, 2024 11:55 12s
May 17, 2024 11:55 12s
After adding a driver to a M584 defined axis, motor doesn't move Auto-close blank templates #213: Issue #1009 opened by droftarts
May 17, 2024 10:21 11s
May 17, 2024 10:21 11s
Bug: setting elements of nested arrays sometimes goes wrong Auto-close blank templates #212: Issue #1008 opened by dc42
May 17, 2024 07:25 11s
May 17, 2024 07:25 11s
Extend events to include Fan Tacho Auto-close blank templates #211: Issue #1007 opened by T3P3
May 16, 2024 12:01 11s
May 16, 2024 12:01 11s
Incorrect extruder steps for G2/G3 moves at low extruder steps/mm Auto-close blank templates #210: Issue #1006 opened by T3P3
May 15, 2024 12:07 12s
May 15, 2024 12:07 12s
Task CPU usage in M122 report can exceed 100% Auto-close blank templates #209: Issue #1005 opened by dc42
May 14, 2024 20:54 12s
May 14, 2024 20:54 12s
Pause and resume, during a restartable macro from a job file, restarts the entire job file Auto-close blank templates #208: Issue #1004 opened by T3P3
May 14, 2024 20:54 16s
May 14, 2024 20:54 16s
Bug: can't create a variable with the same name as a parameter Auto-close blank templates #207: Issue #1003 opened by dc42
May 14, 2024 17:26 12s
May 14, 2024 17:26 12s
[FeatureRequest] Add saving of probe and SZP parameters to config-override.g Auto-close blank templates #206: Issue #1002 opened by droftarts
May 13, 2024 16:06 15s
May 13, 2024 16:06 15s
[FeatureRequest] Add M code to configure CAN_0 and CAN_1 on 6HC/6XD Auto-close blank templates #205: Issue #1000 opened by droftarts
May 13, 2024 13:51 14s
May 13, 2024 13:51 14s