Hardware Compatibility Issues / Success Stories

[JohnBaumb]

Hardware Compatibility & Success Stories

Help us build KlipperFleet compatibility matrix! Since this project is in alpha, we rely on community feedback to verify hardware we don't have in-house.

If you have tested KlipperFleet with your MCUs, please share your results below using this template:

Test Report

• MCU Model: (e.g., BTT Octopus v1.1, SKR 3, MKS Monster8)
• Connection Method: (CAN, UART, USB)
• Bootloader: (Katapult / DFU)
• Bootloader Offset: (e.g., No bootloader, 8KiB, 32KiB)
• Result: ✅ Success / ❌ Issues
• Notes: (Any specific Kconfig options, hardware quirks, etc.)

Why report here?

• Verified Configurations: Your reports will be used to update the README.md compatibility list.
• Community Help: Help other users with the same hardware find the correct settings.
• Roadmap Influence: Hardware with high interest but low compatibility will be prioritized for development.

---

Note: If you encounter a reproducible bug in the software itself, please open a GitHub Issue instead.

[mokshmridul]

MCU Model: BTT EBB36Gen2
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 8KiB
Result: ✅ Success
Notes: Exact settings used below

[ejsears]

MCU Model: BTT Kraken
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 128
Result: ✅ Success
Notes: Flashed with Kalico bleeding edge v2 branch

MCU Model: ebb 36 v1.2
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 8
Result: ✅ Success
Notes: Flashed with Kalico bleeding edge v2 branch

[DrFate09]

MCU Model: QIDI Plus 4 Mainboard
Connection Method: USB
Bootloader: Katapult
Bootloader Offset: 32KiB
Result: ✅ Success
Notes: Kalico firmware

MCU Model: QIDI Plus 4 Toolhead Board
Connection Method: USB to UART
Bootloader: Katapult
Bootloader Offset: 8KiB
Result: ✅ Success
Notes: Data connection over USB to UART Bridge, Kalico firmware

MCU Model: QIDI Box v2
Connection Method: USB
Bootloader: Katapult
Bootloader Offset: 32KiB
Result: ✅ Success
Notes: Kalico firmware

MCU Model: ToqueCAN
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 8KiB
Result: ✅ Success
Notes: Kalico firmware

MCU Model: Raspberry Pi
Connection Method: Linux
Bootloader: N/A
Bootloader Offset: N/A
Result: ✅ Success

[JohnBaumb]

Added kalico support more thoroughly in 30b94b9 (main, latest), let me know how it works.

[ModularPrintingSystem]

MCU Model: Fysetc Spider V2.2
Connection Method: UART
Bootloader: Katapult
Bootloader Offset: 32KiB
Result: ✅ Success

MCU Model: Raspberry Pi
Connection Method: Linux
Bootloader: N/A
Bootloader Offset: N/A
Result: ✅ Success

[ModularPrintingSystem]

MCU Model: Mellow Super 8 Pro (STM32H723)
Connection Method: USB / USB to CAN bus bridge
Bootloader: Katapult
Bootloader Offset: 128KiB
Result: ✅ Success

MCU Model: BTT MMB CAN V1.0 (STM32G0B1)
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 8KiB
Result: ✅ Success

MCU Model: Mellow ADXL345 (RP2040)
Connection Method: USB
Bootloader: Katapult
Bootloader Offset: 16KiB
Result: ✅ Success

[matthew73210]

#Lemontron
MCU Model: Mellow FLY-micro4 + EBB42
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: yes
Result: ✅ Success
Notes: CM4 + BTT PAD7. Kalico

#Sovol Zero
MCU Model: STM32H750 (as usb can bridge) + 2* stm32f103xe
Connection Method: USB --> CAN
Bootloader: Katapult
Bootloader Offset: yes
Result: ✅ Success
Notes: CB1 as SBC. Kalico + eddy-NG

[Cosik]

MCU Model: Duet 2 WiFi
Connection Method: USB
Bootloader: N/A
Bootloader Offset: N/A
Result: ✅ Success
Notes: Even pressing button for flashing was not needed

MCU Model: Due + RampsFDv2
Connection Method: USB
Bootloader: N/A
Bootloader Offset: N/A
Result: ✅ Success
Notes:

MCU Model: sht36v2
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 8
Result: ✅ Success
Notes: Flashed with and without custom make command (have multiple of those boards)

MCU Model: StrideMax
Connection Method: CAN
Bootloader: Katapult
Bootloader Offset: 16
Result: ✅ Success
Notes: