Skip to content

Conversation

kunyi731
Copy link

Procfs read should be npcm7xx_proc_read function so that the read
operation correctly allocates dump memory.

Change-Id: I2bd72fbc5c1668c062c6eb5b95057c7f050b6009
Signed-off-by: Kun Yi [email protected]

tmaimon and others added 30 commits May 10, 2018 17:27
add configuration definition for evaluation board based
NPCM7xx (Poleg) BMC

Signed-off-by: Tomer Maimon <[email protected]>
Add full device tree for all Nuvoton NPCM750 BMCs and a board
specific device tree for the NPCM750 (Poleg) evaluation board.

Based on [v8,2/3] arm: dts: add Nuvoton NPCM750 device tree patch:
Brendan Higgins : - https://patchwork.kernel.org/patch/10063497/

Signed-off-by: Tomer Maimon <[email protected]>
Add maintainers and reviewers for Nuvoton NPCM architecture

Based on [v8,3/3] MAINTAINERS: Add entry for Nuvoton NPCM architecture patch:
Brendan Higgins : - https://patchwork.kernel.org/patch/10063413/

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton NPCM7xx timer.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx timer driver.

the clocksource Enable 24-bit TIMER0 and TIMER1 counters,
while TIMER0 serves as clockevent and TIMER1 serves as clocksource.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton NPCM7xx watchdog.
Add Nuvoton BMC NPCM7xx watchdog driver.

Nuvoton NPCM7xx have three watchdog timer modules, each watchdog timer
is a free-running timer with programmable timeout intervals.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton NPCM UART.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM UART driver.

The NPCM7xx BMC contains four UART blocks and accessory logic.

NPCM UART based on 8250 driver.

Signed-off-by: Tomer Maimon <[email protected]>

Remove NPCM UART based on 8250 driver.
and add to 8250 driver support to NPCM7xx serial

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton NPCM7xx ADC.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx Analog-to-digital
converter (ADC) driver

The NPCM7xx ADC is a 10-bit converter for eight channel
inputs, the ADC module includes an eight-to-one multiplexer.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton
NPCM7xx Serial Peripheral Interface (SPI) NOR

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx serial Peripheral interface (SPI)
Flash interface unit (FIU) driver

Nuvoton NPCM7xx have two SPI nor modules,
first module support 2 chip select
second module support 4 chip select

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton
NPCM7xx Pulse Width Modulation (PWM) and Fan
Tachometer devices.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx Pulse Width Modulation (PWM)
Fan tachometer (Fan) drivers

Nuvoton NPCM7xx support upto 16 Fan tachometer inputs and
upto 8 PWM outputs.
Each PWM output module have watchdog.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for
Nuvoton NPCM7xx pin controller

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx pin controller driver.

The NPCM7XX Pin Controller multi-function routed
through the multiplexing block, Each pin supports
GPIO functionality (GPIOx) and multiple functions
that directly connect the pin to different hardware
blocks.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for
Nuvoton NPCM7xx random number generator.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx random number generator driver.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for
Nuvoton NPCM7xx Ethernet MAC Controller (EMC).

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx Ethernet MAC
controller (EMC) driver.

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for
Nuvoton NPCM7xx I2C bus.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx I2C bus driver.

Signed-off-by: Avi Fishman <[email protected]>
Signed-off-by: Tomer Maimon <[email protected]>
add NPCM7XX clock include file to building DTS

Signed-off-by: Tomer Maimon <[email protected]>
Added device tree binding documentation for Nuvoton NPCM7xx clock.

Signed-off-by: Tomer Maimon <[email protected]>
add NPCM7XX clock include file for DTS use.

Signed-off-by: Tomer Maimon <[email protected]>
Add Nuvoton BMC NPCM7xx clock bus driver.

Signed-off-by: Tomer Maimon <[email protected]>
Bypass for lpi eee hang issue in the
STMicroelectronics 10/100/1000 Ethernet driver

Signed-off-by: Tomer Maimon <[email protected]>
The KCS (Keyboard Controller Style) interface is used to perform in-band
IPMI communication between a server host and its BMC (BaseBoard Management
Controllers).

This driver exposes the KCS interface on ASpeed SOCs (AST2400 and AST2500)
as a character device. Such SOCs are commonly used as BMCs and this driver
implements the BMC side of the KCS interface.

Signed-off-by: Haiyue Wang <[email protected]>
avifishman and others added 6 commits June 11, 2018 20:18
Original kcs_bmc_npcm7xx.c was missing enabling to send interrupt to the
host on writes to output buffer.
This patch fixes it by setting the bits that enables the generation of
IRQn events by hardware control based on the status of the OBF flag.

Signed-off-by: Avi Fishman <[email protected]>
enable NPCM7XX_TIMER by defualt when the NPCM7XX
architecture is selected

Signed-off-by: Tomer Maimon <[email protected]>
Adding multiplexer support for handling control SPSWC register

Signed-off-by: Tomer Maimon <[email protected]>
Procfs read should be npcm7xx_proc_read function so that the read
operation correctly allocates dump memory.

Change-Id: I2bd72fbc5c1668c062c6eb5b95057c7f050b6009
Signed-off-by: Kun Yi <[email protected]>
@avifishman
Copy link
Member

avifishman commented Jun 18, 2018 via email

@kunyi731
Copy link
Author

kunyi731 commented Jun 18, 2018 via email

@avifishman
Copy link
Member

avifishman commented Jun 19, 2018 via email

@tmaimon tmaimon force-pushed the Poleg-4.13.16-OpenBMC-Upstream branch from 33be98a to 96c2824 Compare June 20, 2018 08:31
@tmaimon tmaimon force-pushed the Poleg-4.13.16-OpenBMC-Upstream branch 4 times, most recently from 5ed6593 to 836c6f7 Compare July 1, 2018 13:41
BenjaminFair pushed a commit to BenjaminFair/linux that referenced this pull request Jul 9, 2018
commit 1105a2f upstream.

In our armv8a server(QDF2400), I noticed lots of WARN_ON caused by
PAGE_SIZE unaligned for rmap_item->address under memory pressure
tests(start 20 guests and run memhog in the host).

  WARNING: CPU: 4 PID: 4641 at virt/kvm/arm/mmu.c:1826 kvm_age_hva_handler+0xc0/0xc8
  CPU: 4 PID: 4641 Comm: memhog Tainted: G        W 4.17.0-rc3+ Nuvoton-Israel#8
  Call trace:
   kvm_age_hva_handler+0xc0/0xc8
   handle_hva_to_gpa+0xa8/0xe0
   kvm_age_hva+0x4c/0xe8
   kvm_mmu_notifier_clear_flush_young+0x54/0x98
   __mmu_notifier_clear_flush_young+0x6c/0xa0
   page_referenced_one+0x154/0x1d8
   rmap_walk_ksm+0x12c/0x1d0
   rmap_walk+0x94/0xa0
   page_referenced+0x194/0x1b0
   shrink_page_list+0x674/0xc28
   shrink_inactive_list+0x26c/0x5b8
   shrink_node_memcg+0x35c/0x620
   shrink_node+0x100/0x430
   do_try_to_free_pages+0xe0/0x3a8
   try_to_free_pages+0xe4/0x230
   __alloc_pages_nodemask+0x564/0xdc0
   alloc_pages_vma+0x90/0x228
   do_anonymous_page+0xc8/0x4d0
   __handle_mm_fault+0x4a0/0x508
   handle_mm_fault+0xf8/0x1b0
   do_page_fault+0x218/0x4b8
   do_translation_fault+0x90/0xa0
   do_mem_abort+0x68/0xf0
   el0_da+0x24/0x28

In rmap_walk_ksm, the rmap_item->address might still have the
STABLE_FLAG, then the start and end in handle_hva_to_gpa might not be
PAGE_SIZE aligned.  Thus it will cause exceptions in handle_hva_to_gpa
on arm64.

This patch fixes it by ignoring (not removing) the low bits of address
when doing rmap_walk_ksm.

IMO, it should be backported to stable tree.  the storm of WARN_ONs is
very easy for me to reproduce.  More than that, I watched a panic (not
reproducible) as follows:

  page:ffff7fe003742d80 count:-4871 mapcount:-2126053375 mapping: (null) index:0x0
  flags: 0x1fffc00000000000()
  raw: 1fffc00000000000 0000000000000000 0000000000000000 ffffecf981470000
  raw: dead000000000100 dead000000000200 ffff8017c001c000 0000000000000000
  page dumped because: nonzero _refcount
  CPU: 29 PID: 18323 Comm: qemu-kvm Tainted: G W 4.14.15-5.hxt.aarch64 Nuvoton-Israel#1
  Hardware name: <snip for confidential issues>
  Call trace:
    dump_backtrace+0x0/0x22c
    show_stack+0x24/0x2c
    dump_stack+0x8c/0xb0
    bad_page+0xf4/0x154
    free_pages_check_bad+0x90/0x9c
    free_pcppages_bulk+0x464/0x518
    free_hot_cold_page+0x22c/0x300
    __put_page+0x54/0x60
    unmap_stage2_range+0x170/0x2b4
    kvm_unmap_hva_handler+0x30/0x40
    handle_hva_to_gpa+0xb0/0xec
    kvm_unmap_hva_range+0x5c/0xd0

I even injected a fault on purpose in kvm_unmap_hva_range by seting
size=size-0x200, the call trace is similar as above.  So I thought the
panic is similarly caused by the root cause of WARN_ON.

Andrea said:

: It looks a straightforward safe fix, on x86 hva_to_gfn_memslot would
: zap those bits and hide the misalignment caused by the low metadata
: bits being erroneously left set in the address, but the arm code
: notices when that's the last page in the memslot and the hva_end is
: getting aligned and the size is below one page.
:
: I think the problem triggers in the addr += PAGE_SIZE of
: unmap_stage2_ptes that never matches end because end is aligned but
: addr is not.
:
: 	} while (pte++, addr += PAGE_SIZE, addr != end);
:
: x86 again only works on hva_start/hva_end after converting it to
: gfn_start/end and that being in pfn units the bits are zapped before
: they risk to cause trouble.

Jia He said:

: I've tested by myself in arm64 server (QDF2400,46 cpus,96G mem) Without
: this patch, the WARN_ON is very easy for reproducing.  After this patch, I
: have run the same benchmarch for a whole day without any WARN_ONs

Link: http://lkml.kernel.org/r/[email protected]
Signed-off-by: Jia He <[email protected]>
Reviewed-by: Andrea Arcangeli <[email protected]>
Tested-by: Jia He <[email protected]>
Cc: Suzuki K Poulose <[email protected]>
Cc: Minchan Kim <[email protected]>
Cc: Claudio Imbrenda <[email protected]>
Cc: Arvind Yadav <[email protected]>
Cc: Mike Rapoport <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Linus Torvalds <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
BenjaminFair pushed a commit to BenjaminFair/linux that referenced this pull request Jul 20, 2018
commit b2ca374 upstream.

syzbot hit the following crash on upstream commit
87ef120 (Wed Apr 18 19:48:17 2018 +0000)
Merge tag 'ceph-for-4.17-rc2' of git://github.com/ceph/ceph-client
syzbot dashboard link: https://syzkaller.appspot.com/bug?extid=83699adeb2d13579c31e

C reproducer: https://syzkaller.appspot.com/x/repro.c?id=5805208181407744
syzkaller reproducer: https://syzkaller.appspot.com/x/repro.syz?id=6005073343676416
Raw console output: https://syzkaller.appspot.com/x/log.txt?id=6555047731134464
Kernel config: https://syzkaller.appspot.com/x/.config?id=1808800213120130118
compiler: gcc (GCC) 8.0.1 20180413 (experimental)

IMPORTANT: if you fix the bug, please add the following tag to the commit:
Reported-by: [email protected]
It will help syzbot understand when the bug is fixed. See footer for details.
If you forward the report, please keep this part and the footer.

F2FS-fs (loop0): Magic Mismatch, valid(0xf2f52010) - read(0x0)
F2FS-fs (loop0): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (loop0): invalid crc value
BUG: unable to handle kernel paging request at ffffed006b2a50c0
PGD 21ffee067 P4D 21ffee067 PUD 21fbeb067 PMD 0
Oops: 0000 [Nuvoton-Israel#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 4514 Comm: syzkaller989480 Not tainted 4.17.0-rc1+ Nuvoton-Israel#8
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:build_sit_entries fs/f2fs/segment.c:3653 [inline]
RIP: 0010:build_segment_manager+0x7ef7/0xbf70 fs/f2fs/segment.c:3852
RSP: 0018:ffff8801b102e5b0 EFLAGS: 00010a06
RAX: 1ffff1006b2a50c0 RBX: 0000000000000004 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8801ac74243e
RBP: ffff8801b102f410 R08: ffff8801acbd46c0 R09: fffffbfff14d9af8
R10: fffffbfff14d9af8 R11: ffff8801acbd46c0 R12: ffff8801ac742a80
R13: ffff8801d9519100 R14: dffffc0000000000 R15: ffff880359528600
FS:  0000000001e04880(0000) GS:ffff8801dae00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffed006b2a50c0 CR3: 00000001ac6ac000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 f2fs_fill_super+0x4095/0x7bf0 fs/f2fs/super.c:2803
 mount_bdev+0x30c/0x3e0 fs/super.c:1165
 f2fs_mount+0x34/0x40 fs/f2fs/super.c:3020
 mount_fs+0xae/0x328 fs/super.c:1268
 vfs_kern_mount.part.34+0xd4/0x4d0 fs/namespace.c:1037
 vfs_kern_mount fs/namespace.c:1027 [inline]
 do_new_mount fs/namespace.c:2517 [inline]
 do_mount+0x564/0x3070 fs/namespace.c:2847
 ksys_mount+0x12d/0x140 fs/namespace.c:3063
 __do_sys_mount fs/namespace.c:3077 [inline]
 __se_sys_mount fs/namespace.c:3074 [inline]
 __x64_sys_mount+0xbe/0x150 fs/namespace.c:3074
 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x443d6a
RSP: 002b:00007ffd312813c8 EFLAGS: 00000297 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 0000000020000c00 RCX: 0000000000443d6a
RDX: 0000000020000000 RSI: 0000000020000100 RDI: 00007ffd312813d0
RBP: 0000000000000003 R08: 0000000020016a00 R09: 000000000000000a
R10: 0000000000000000 R11: 0000000000000297 R12: 0000000000000004
R13: 0000000000402c60 R14: 0000000000000000 R15: 0000000000000000
RIP: build_sit_entries fs/f2fs/segment.c:3653 [inline] RSP: ffff8801b102e5b0
RIP: build_segment_manager+0x7ef7/0xbf70 fs/f2fs/segment.c:3852 RSP: ffff8801b102e5b0
CR2: ffffed006b2a50c0
---[ end trace a2034989e196ff17 ]---

Reported-and-tested-by: [email protected]
Reviewed-by: Chao Yu <[email protected]>
Signed-off-by: Jaegeuk Kim <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
@tmaimon tmaimon force-pushed the Poleg-4.13.16-OpenBMC-Upstream branch from 56e5af0 to 5771681 Compare July 24, 2018 19:44
BenjaminFair pushed a commit to BenjaminFair/linux that referenced this pull request Sep 6, 2018
commit 36eb8ff upstream.

Crash dump shows following instructions

crash> bt
PID: 0      TASK: ffffffffbe412480  CPU: 0   COMMAND: "swapper/0"
 #0 [ffff891ee0003868] machine_kexec at ffffffffbd063ef1
 Nuvoton-Israel#1 [ffff891ee00038c8] __crash_kexec at ffffffffbd12b6f2
 Nuvoton-Israel#2 [ffff891ee0003998] crash_kexec at ffffffffbd12c84c
 Nuvoton-Israel#3 [ffff891ee00039b8] oops_end at ffffffffbd030f0a
 Nuvoton-Israel#4 [ffff891ee00039e0] no_context at ffffffffbd074643
 Nuvoton-Israel#5 [ffff891ee0003a40] __bad_area_nosemaphore at ffffffffbd07496e
 Nuvoton-Israel#6 [ffff891ee0003a90] bad_area_nosemaphore at ffffffffbd074a64
 Nuvoton-Israel#7 [ffff891ee0003aa0] __do_page_fault at ffffffffbd074b0a
 Nuvoton-Israel#8 [ffff891ee0003b18] do_page_fault at ffffffffbd074fc8
 Nuvoton-Israel#9 [ffff891ee0003b50] page_fault at ffffffffbda01925
    [exception RIP: qlt_schedule_sess_for_deletion+15]
    RIP: ffffffffc02e526f  RSP: ffff891ee0003c08  RFLAGS: 00010046
    RAX: 0000000000000000  RBX: 0000000000000000  RCX: ffffffffc0307847
    RDX: 00000000000020e6  RSI: ffff891edbc377c8  RDI: 0000000000000000
    RBP: ffff891ee0003c18   R8: ffffffffc02f0b20   R9: 0000000000000250
    R10: 0000000000000258  R11: 000000000000b780  R12: ffff891ed9b43000
    R13: 00000000000000f0  R14: 0000000000000006  R15: ffff891edbc377c8
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 Nuvoton-Israel#10 [ffff891ee0003c20] qla2x00_fcport_event_handler at ffffffffc02853d3 [qla2xxx]
 Nuvoton-Israel#11 [ffff891ee0003cf0] __dta_qla24xx_async_gnl_sp_done_333 at ffffffffc0285a1d [qla2xxx]
 Nuvoton-Israel#12 [ffff891ee0003de8] qla24xx_process_response_queue at ffffffffc02a2eb5 [qla2xxx]
 Nuvoton-Israel#13 [ffff891ee0003e88] qla24xx_msix_rsp_q at ffffffffc02a5403 [qla2xxx]
 Nuvoton-Israel#14 [ffff891ee0003ec0] __handle_irq_event_percpu at ffffffffbd0f4c59
 Nuvoton-Israel#15 [ffff891ee0003f10] handle_irq_event_percpu at ffffffffbd0f4e02
 Nuvoton-Israel#16 [ffff891ee0003f40] handle_irq_event at ffffffffbd0f4e90
 Nuvoton-Israel#17 [ffff891ee0003f68] handle_edge_irq at ffffffffbd0f8984
 Nuvoton-Israel#18 [ffff891ee0003f88] handle_irq at ffffffffbd0305d5
 Nuvoton-Israel#19 [ffff891ee0003fb8] do_IRQ at ffffffffbda02a18
 --- <IRQ stack> ---
 Nuvoton-Israel#20 [ffffffffbe403d30] ret_from_intr at ffffffffbda0094e
    [exception RIP: unknown or invalid address]
    RIP: 000000000000001f  RSP: 0000000000000000  RFLAGS: fff3b8c2091ebb3f
    RAX: ffffbba5a0000200  RBX: 0000be8cdfa8f9fa  RCX: 0000000000000018
    RDX: 0000000000000101  RSI: 000000000000015d  RDI: 0000000000000193
    RBP: 0000000000000083   R8: ffffffffbe403e38   R9: 0000000000000002
    R10: 0000000000000000  R11: ffffffffbe56b820  R12: ffff891ee001cf00
    R13: ffffffffbd11c0a4  R14: ffffffffbe403d60  R15: 0000000000000001
    ORIG_RAX: ffff891ee0022ac0  CS: 0000  SS: ffffffffffffffb9
 bt: WARNING: possibly bogus exception frame
 Nuvoton-Israel#21 [ffffffffbe403dd8] cpuidle_enter_state at ffffffffbd67c6fd
 Nuvoton-Israel#22 [ffffffffbe403e40] cpuidle_enter at ffffffffbd67c907
 Nuvoton-Israel#23 [ffffffffbe403e50] call_cpuidle at ffffffffbd0d98f3
 Nuvoton-Israel#24 [ffffffffbe403e60] do_idle at ffffffffbd0d9b42
 Nuvoton-Israel#25 [ffffffffbe403e98] cpu_startup_entry at ffffffffbd0d9da3
 Nuvoton-Israel#26 [ffffffffbe403ec0] rest_init at ffffffffbd81d4aa
 Nuvoton-Israel#27 [ffffffffbe403ed0] start_kernel at ffffffffbe67d2ca
 Nuvoton-Israel#28 [ffffffffbe403f28] x86_64_start_reservations at ffffffffbe67c675
 Nuvoton-Israel#29 [ffffffffbe403f38] x86_64_start_kernel at ffffffffbe67c6eb
 Nuvoton-Israel#30 [ffffffffbe403f50] secondary_startup_64 at ffffffffbd0000d5

Fixes: 040036b ("scsi: qla2xxx: Delay loop id allocation at login")
Cc: <[email protected]> # v4.17+
Signed-off-by: Chuck Anderson <[email protected]>
Signed-off-by: Himanshu Madhani <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
BenjaminFair pushed a commit to BenjaminFair/linux that referenced this pull request Sep 6, 2018
[ Upstream commit 4f4616c ]

Similar to what we do when we remove a PCI function, set the
QEDF_UNLOADING flag to prevent any requests from being queued while a
vport is being deleted.  This prevents any requests from getting stuck
in limbo when the vport is unloaded or deleted.

Fixes the crash:

PID: 106676  TASK: ffff9a436aa90000  CPU: 12  COMMAND: "multipathd"
 #0 [ffff9a43567d3550] machine_kexec+522 at ffffffffaca60b2a
 Nuvoton-Israel#1 [ffff9a43567d35b0] __crash_kexec+114 at ffffffffacb13512
 Nuvoton-Israel#2 [ffff9a43567d3680] crash_kexec+48 at ffffffffacb13600
 Nuvoton-Israel#3 [ffff9a43567d3698] oops_end+168 at ffffffffad117768
 Nuvoton-Israel#4 [ffff9a43567d36c0] no_context+645 at ffffffffad106f52
 Nuvoton-Israel#5 [ffff9a43567d3710] __bad_area_nosemaphore+116 at ffffffffad106fe9
 Nuvoton-Israel#6 [ffff9a43567d3760] bad_area+70 at ffffffffad107379
 Nuvoton-Israel#7 [ffff9a43567d3788] __do_page_fault+1247 at ffffffffad11a8cf
 Nuvoton-Israel#8 [ffff9a43567d37f0] do_page_fault+53 at ffffffffad11a915
 Nuvoton-Israel#9 [ffff9a43567d3820] page_fault+40 at ffffffffad116768
    [exception RIP: qedf_init_task+61]
    RIP: ffffffffc0e13c2d  RSP: ffff9a43567d38d0  RFLAGS: 00010046
    RAX: 0000000000000000  RBX: ffffbe920472c738  RCX: ffff9a434fa0e3e8
    RDX: ffff9a434f695280  RSI: ffffbe920472c738  RDI: ffff9a43aa359c80
    RBP: ffff9a43567d3950   R8: 0000000000000c15   R9: ffff9a3fb09b9880
    R10: ffff9a434fa0e3e8  R11: ffff9a43567d35ce  R12: 0000000000000000
    R13: ffff9a434f695280  R14: ffff9a43aa359c80  R15: ffff9a3fb9e005c0
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018

Signed-off-by: Chad Dupuis <[email protected]>
Signed-off-by: Martin K. Petersen <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
BenjaminFair pushed a commit to BenjaminFair/linux that referenced this pull request Sep 6, 2018
commit 89da619 upstream.

Kernel panic when with high memory pressure, calltrace looks like,

PID: 21439 TASK: ffff881be3afedd0 CPU: 16 COMMAND: "java"
 #0 [ffff881ec7ed7630] machine_kexec at ffffffff81059beb
 Nuvoton-Israel#1 [ffff881ec7ed7690] __crash_kexec at ffffffff81105942
 Nuvoton-Israel#2 [ffff881ec7ed7760] crash_kexec at ffffffff81105a30
 Nuvoton-Israel#3 [ffff881ec7ed7778] oops_end at ffffffff816902c8
 Nuvoton-Israel#4 [ffff881ec7ed77a0] no_context at ffffffff8167ff46
 Nuvoton-Israel#5 [ffff881ec7ed77f0] __bad_area_nosemaphore at ffffffff8167ffdc
 Nuvoton-Israel#6 [ffff881ec7ed7838] __node_set at ffffffff81680300
 Nuvoton-Israel#7 [ffff881ec7ed7860] __do_page_fault at ffffffff8169320f
 Nuvoton-Israel#8 [ffff881ec7ed78c0] do_page_fault at ffffffff816932b5
 Nuvoton-Israel#9 [ffff881ec7ed78f0] page_fault at ffffffff8168f4c8
    [exception RIP: _raw_spin_lock_irqsave+47]
    RIP: ffffffff8168edef RSP: ffff881ec7ed79a8 RFLAGS: 00010046
    RAX: 0000000000000246 RBX: ffffea0019740d00 RCX: ffff881ec7ed7fd8
    RDX: 0000000000020000 RSI: 0000000000000016 RDI: 0000000000000008
    RBP: ffff881ec7ed79a8 R8: 0000000000000246 R9: 000000000001a098
    R10: ffff88107ffda000 R11: 0000000000000000 R12: 0000000000000000
    R13: 0000000000000008 R14: ffff881ec7ed7a80 R15: ffff881be3afedd0
    ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018

It happens in the pagefault and results in double pagefault
during compacting pages when memory allocation fails.

Analysed the vmcore, the page leads to second pagefault is corrupted
with _mapcount=-256, but private=0.

It's caused by the race between migration and ballooning, and lock
missing in virtballoon_migratepage() of virtio_balloon driver.
This patch fix the bug.

Fixes: e225042 ("virtio_balloon: introduce migration primitives to balloon pages")
Cc: [email protected]
Signed-off-by: Jiang Biao <[email protected]>
Signed-off-by: Huang Chong <[email protected]>
Signed-off-by: Michael S. Tsirkin <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
warp5tw pushed a commit to warp5tw/linux that referenced this pull request Jan 10, 2022
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.

The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ Nuvoton-Israel#8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================

The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.

Signed-off-by: William Zhao <[email protected]>
Signed-off-by: David S. Miller <[email protected]>
warp5tw pushed a commit to warp5tw/linux that referenced this pull request Mar 8, 2022
We hit a bug with a recovering relocation on mount for one of our file
systems in production.  I reproduced this locally by injecting errors
into snapshot delete with balance running at the same time.  This
presented as an error while looking up an extent item

  WARNING: CPU: 5 PID: 1501 at fs/btrfs/extent-tree.c:866 lookup_inline_extent_backref+0x647/0x680
  CPU: 5 PID: 1501 Comm: btrfs-balance Not tainted 5.16.0-rc8+ Nuvoton-Israel#8
  RIP: 0010:lookup_inline_extent_backref+0x647/0x680
  RSP: 0018:ffffae0a023ab960 EFLAGS: 00010202
  RAX: 0000000000000001 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: 000000000000000c RDI: 0000000000000000
  RBP: ffff943fd2a39b60 R08: 0000000000000000 R09: 0000000000000001
  R10: 0001434088152de0 R11: 0000000000000000 R12: 0000000001d05000
  R13: ffff943fd2a39b60 R14: ffff943fdb96f2a0 R15: ffff9442fc923000
  FS:  0000000000000000(0000) GS:ffff944e9eb40000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00007f1157b1fca8 CR3: 000000010f092000 CR4: 0000000000350ee0
  Call Trace:
   <TASK>
   insert_inline_extent_backref+0x46/0xd0
   __btrfs_inc_extent_ref.isra.0+0x5f/0x200
   ? btrfs_merge_delayed_refs+0x164/0x190
   __btrfs_run_delayed_refs+0x561/0xfa0
   ? btrfs_search_slot+0x7b4/0xb30
   ? btrfs_update_root+0x1a9/0x2c0
   btrfs_run_delayed_refs+0x73/0x1f0
   ? btrfs_update_root+0x1a9/0x2c0
   btrfs_commit_transaction+0x50/0xa50
   ? btrfs_update_reloc_root+0x122/0x220
   prepare_to_merge+0x29f/0x320
   relocate_block_group+0x2b8/0x550
   btrfs_relocate_block_group+0x1a6/0x350
   btrfs_relocate_chunk+0x27/0xe0
   btrfs_balance+0x777/0xe60
   balance_kthread+0x35/0x50
   ? btrfs_balance+0xe60/0xe60
   kthread+0x16b/0x190
   ? set_kthread_struct+0x40/0x40
   ret_from_fork+0x22/0x30
   </TASK>

Normally snapshot deletion and relocation are excluded from running at
the same time by the fs_info->cleaner_mutex.  However if we had a
pending balance waiting to get the ->cleaner_mutex, and a snapshot
deletion was running, and then the box crashed, we would come up in a
state where we have a half deleted snapshot.

Again, in the normal case the snapshot deletion needs to complete before
relocation can start, but in this case relocation could very well start
before the snapshot deletion completes, as we simply add the root to the
dead roots list and wait for the next time the cleaner runs to clean up
the snapshot.

Fix this by setting a bit on the fs_info if we have any DEAD_ROOT's that
had a pending drop_progress key.  If they do then we know we were in the
middle of the drop operation and set a flag on the fs_info.  Then
balance can wait until this flag is cleared to start up again.

If there are DEAD_ROOT's that don't have a drop_progress set then we're
safe to start balance right away as we'll be properly protected by the
cleaner_mutex.

CC: [email protected] # 5.10+
Reviewed-by: Filipe Manana <[email protected]>
Signed-off-by: Josef Bacik <[email protected]>
Reviewed-by: David Sterba <[email protected]>
Signed-off-by: David Sterba <[email protected]>
warp5tw pushed a commit to warp5tw/linux that referenced this pull request May 24, 2022
Do not allow to write timestamps on RX rings if PF is being configured.
When PF is being configured RX rings can be freed or rebuilt. If at the
same time timestamps are updated, the kernel will crash by dereferencing
null RX ring pointer.

PID: 1449   TASK: ff187d28ed658040  CPU: 34  COMMAND: "ice-ptp-0000:51"
 #0 [ff1966a94a713bb0] machine_kexec at ffffffff9d05a0be
 Nuvoton-Israel#1 [ff1966a94a713c08] __crash_kexec at ffffffff9d192e9d
 Nuvoton-Israel#2 [ff1966a94a713cd0] crash_kexec at ffffffff9d1941bd
 Nuvoton-Israel#3 [ff1966a94a713ce8] oops_end at ffffffff9d01bd54
 Nuvoton-Israel#4 [ff1966a94a713d08] no_context at ffffffff9d06bda4
 Nuvoton-Israel#5 [ff1966a94a713d60] __bad_area_nosemaphore at ffffffff9d06c10c
 Nuvoton-Israel#6 [ff1966a94a713da8] do_page_fault at ffffffff9d06cae4
 Nuvoton-Israel#7 [ff1966a94a713de0] page_fault at ffffffff9da0107e
    [exception RIP: ice_ptp_update_cached_phctime+91]
    RIP: ffffffffc076db8b  RSP: ff1966a94a713e98  RFLAGS: 00010246
    RAX: 16e3db9c6b7ccae4  RBX: ff187d269dd3c180  RCX: ff187d269cd4d018
    RDX: 0000000000000000  RSI: 0000000000000000  RDI: 0000000000000000
    RBP: ff187d269cfcc644   R8: ff187d339b9641b0   R9: 0000000000000000
    R10: 0000000000000002  R11: 0000000000000000  R12: ff187d269cfcc648
    R13: ffffffff9f128784  R14: ffffffff9d101b70  R15: ff187d269cfcc640
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 Nuvoton-Israel#8 [ff1966a94a713ea0] ice_ptp_periodic_work at ffffffffc076dbef [ice]
 Nuvoton-Israel#9 [ff1966a94a713ee0] kthread_worker_fn at ffffffff9d101c1b
 Nuvoton-Israel#10 [ff1966a94a713f10] kthread at ffffffff9d101b4d
 Nuvoton-Israel#11 [ff1966a94a713f50] ret_from_fork at ffffffff9da0023f

Fixes: 77a7811 ("ice: enable receive hardware timestamping")
Signed-off-by: Arkadiusz Kubalewski <[email protected]>
Reviewed-by: Michal Schmidt <[email protected]>
Tested-by: Dave Cain <[email protected]>
Tested-by: Gurucharan <[email protected]> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <[email protected]>
tmaimon pushed a commit that referenced this pull request Aug 7, 2024
commit be346c1 upstream.

The code in ocfs2_dio_end_io_write() estimates number of necessary
transaction credits using ocfs2_calc_extend_credits().  This however does
not take into account that the IO could be arbitrarily large and can
contain arbitrary number of extents.

Extent tree manipulations do often extend the current transaction but not
in all of the cases.  For example if we have only single block extents in
the tree, ocfs2_mark_extent_written() will end up calling
ocfs2_replace_extent_rec() all the time and we will never extend the
current transaction and eventually exhaust all the transaction credits if
the IO contains many single block extents.  Once that happens a
WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in
jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to
this error.  This was actually triggered by one of our customers on a
heavily fragmented OCFS2 filesystem.

To fix the issue make sure the transaction always has enough credits for
one extent insert before each call of ocfs2_mark_extent_written().

Heming Zhao said:

------
PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error"

PID: xxx  TASK: xxxx  CPU: 5  COMMAND: "SubmitThread-CA"
  #0 machine_kexec at ffffffff8c069932
  #1 __crash_kexec at ffffffff8c1338fa
  #2 panic at ffffffff8c1d69b9
  #3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2]
  #4 __ocfs2_abort at ffffffffc0c88387 [ocfs2]
  #5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2]
  #6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2]
  #7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2]
  #8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2]
  #9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2]
#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2]
#11 dio_complete at ffffffff8c2b9fa7
#12 do_blockdev_direct_IO at ffffffff8c2bc09f
#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2]
#14 generic_file_direct_write at ffffffff8c1dcf14
#15 __generic_file_write_iter at ffffffff8c1dd07b
#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2]
#17 aio_write at ffffffff8c2cc72e
#18 kmem_cache_alloc at ffffffff8c248dde
#19 do_io_submit at ffffffff8c2ccada
#20 do_syscall_64 at ffffffff8c004984
#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba

Link: https://lkml.kernel.org/r/[email protected]
Link: https://lkml.kernel.org/r/[email protected]
Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io")
Signed-off-by: Jan Kara <[email protected]>
Reviewed-by: Joseph Qi <[email protected]>
Reviewed-by: Heming Zhao <[email protected]>
Cc: Mark Fasheh <[email protected]>
Cc: Joel Becker <[email protected]>
Cc: Junxiao Bi <[email protected]>
Cc: Changwei Ge <[email protected]>
Cc: Gang He <[email protected]>
Cc: Jun Piao <[email protected]>
Cc: <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 4, 2024
[ Upstream commit 73f3508 ]

When creating a trace_probe we would set nr_args prior to truncating the
arguments to MAX_TRACE_ARGS. However, we would only initialize arguments
up to the limit.

This caused invalid memory access when attempting to set up probes with
more than 128 fetchargs.

  BUG: kernel NULL pointer dereference, address: 0000000000000020
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD 0 P4D 0
  Oops: Oops: 0000 [#1] PREEMPT SMP PTI
  CPU: 0 UID: 0 PID: 1769 Comm: cat Not tainted 6.11.0-rc7+ #8
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-1.fc39 04/01/2014
  RIP: 0010:__set_print_fmt+0x134/0x330

Resolve the issue by applying the MAX_TRACE_ARGS limit earlier. Return
an error when there are too many arguments instead of silently
truncating.

Link: https://lore.kernel.org/all/[email protected]/

Fixes: 035ba76 ("tracing/probes: cleanup: Set trace_probe::nr_args at trace_probe_init")
Signed-off-by: Mikel Rychliski <[email protected]>
Signed-off-by: Masami Hiramatsu (Google) <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 5, 2024
commit ac01c8c upstream.

AddressSanitizer found a use-after-free bug in the symbol code which
manifested as 'perf top' segfaulting.

  ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80
  READ of size 1 at 0x60b00c48844b thread T193
      #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310
      #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286
      #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614
      #3 0x5650d804568f in __hists__add_entry util/hist.c:754
      #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772
      #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997
      #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242
      #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845
      #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208
      #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245
      #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324
      #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120
      #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442
      #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81

When updating hist maps it's also necessary to update the hist symbol
reference because the old one gets freed in map__put().

While this bug was probably introduced with 5c24b67 ("perf
tools: Replace map->referenced & maps->removed_maps with map->refcnt"),
the symbol objects were leaked until c087e94 ("perf machine:
Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so
the bug was masked.

Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL")
Reported-by: Yunzhao Li <[email protected]>
Signed-off-by: Matt Fleming (Cloudflare) <[email protected]>
Cc: Ian Rogers <[email protected]>
Cc: [email protected]
Cc: Namhyung Kim <[email protected]>
Cc: Riccardo Mancini <[email protected]>
Cc: [email protected] # v5.13+
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 5, 2024
commit 9af2efe upstream.

The fields in the hist_entry are filled on-demand which means they only
have meaningful values when relevant sort keys are used.

So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in
the hist entry can be garbage.  So it shouldn't access it
unconditionally.

I got a segfault, when I wanted to see cgroup profiles.

  $ sudo perf record -a --all-cgroups --synth=cgroup true

  $ sudo perf report -s cgroup

  Program received signal SIGSEGV, Segmentation fault.
  0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48
  48		return RC_CHK_ACCESS(map)->dso;
  (gdb) bt
  #0  0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48
  #1  0x00005555557aa39b in map__load (map=0x0) at util/map.c:344
  #2  0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385
  #3  0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true)
      at util/hist.c:644
  #4  0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0,
      block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761
  #5  0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0,
      sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779
  #6  0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015
  #7  0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0)
      at util/hist.c:1260
  #8  0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0,
      machine=0x5555560388e8) at builtin-report.c:334
  #9  0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128,
      sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232
  #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128,
      sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271
  #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0,
      file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354
  #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132
  #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245
  #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324
  #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342
  #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60)
      at util/session.c:780
  #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688,
      file_path=0x555556038ff0 "perf.data") at util/session.c:1406

As you can see the entry->ms.map was NULL even if he->ms.map has a
value.  This is because 'sym' sort key is not given, so it cannot assume
whether he->ms.sym and entry->ms.sym is the same.  I only checked the
'sym' sort key here as it implies 'dso' behavior (so maps are the same).

Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps")
Signed-off-by: Namhyung Kim <[email protected]>
Cc: Adrian Hunter <[email protected]>
Cc: Ian Rogers <[email protected]>
Cc: Ingo Molnar <[email protected]>
Cc: Jiri Olsa <[email protected]>
Cc: Kan Liang <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Peter Zijlstra <[email protected]>
Cc: Stephane Eranian <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 5, 2024
…tion to perf_sched__replay()

[ Upstream commit c690786 ]

The start_work_mutex and work_done_wait_mutex are used only for the
'perf sched replay'. Put their initialization in perf_sched__replay () to
reduce unnecessary actions in other commands.

Simple functional testing:

  # perf sched record perf bench sched messaging
  # Running 'sched/messaging' benchmark:
  # 20 sender and receiver processes per group
  # 10 groups == 400 processes run

       Total time: 0.197 [sec]
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 14.952 MB perf.data (134165 samples) ]

  # perf sched replay
  run measurement overhead: 108 nsecs
  sleep measurement overhead: 65658 nsecs
  the run test took 999991 nsecs
  the sleep test took 1079324 nsecs
  nr_run_events:        42378
  nr_sleep_events:      43102
  nr_wakeup_events:     31852
  target-less wakeups:  17
  multi-target wakeups: 712
  task      0 (             swapper:         0), nr_events: 10451
  task      1 (             swapper:         1), nr_events: 3
  task      2 (             swapper:         2), nr_events: 1
  <SNIP>
  task    717 (     sched-messaging:     74483), nr_events: 152
  task    718 (     sched-messaging:     74484), nr_events: 1944
  task    719 (     sched-messaging:     74485), nr_events: 73
  task    720 (     sched-messaging:     74486), nr_events: 163
  task    721 (     sched-messaging:     74487), nr_events: 942
  task    722 (     sched-messaging:     74488), nr_events: 78
  task    723 (     sched-messaging:     74489), nr_events: 1090
  ------------------------------------------------------------
  #1  : 1366.507, ravg: 1366.51, cpu: 7682.70 / 7682.70
  #2  : 1410.072, ravg: 1370.86, cpu: 7723.88 / 7686.82
  #3  : 1396.296, ravg: 1373.41, cpu: 7568.20 / 7674.96
  #4  : 1381.019, ravg: 1374.17, cpu: 7531.81 / 7660.64
  #5  : 1393.826, ravg: 1376.13, cpu: 7725.25 / 7667.11
  #6  : 1401.581, ravg: 1378.68, cpu: 7594.82 / 7659.88
  #7  : 1381.337, ravg: 1378.94, cpu: 7371.22 / 7631.01
  #8  : 1373.842, ravg: 1378.43, cpu: 7894.92 / 7657.40
  #9  : 1364.697, ravg: 1377.06, cpu: 7324.91 / 7624.15
  #10 : 1363.613, ravg: 1375.72, cpu: 7209.55 / 7582.69
  # echo $?
  0

Signed-off-by: Yang Jihong <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string")
Signed-off-by: Sasha Levin <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 5, 2024
…f_sched__{lat|map|replay}()

[ Upstream commit bd2cdf2 ]

The curr_pid and cpu_last_switched are used only for the
'perf sched replay/latency/map'. Put their initialization in
perf_sched__{lat|map|replay () to reduce unnecessary actions in other
commands.

Simple functional testing:

  # perf sched record perf bench sched messaging
  # Running 'sched/messaging' benchmark:
  # 20 sender and receiver processes per group
  # 10 groups == 400 processes run

       Total time: 0.209 [sec]
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 16.456 MB perf.data (147907 samples) ]

  # perf sched lat

   -------------------------------------------------------------------------------------------------------------------------------------------
    Task                  |   Runtime ms  | Switches | Avg delay ms    | Max delay ms    | Max delay start           | Max delay end          |
   -------------------------------------------------------------------------------------------------------------------------------------------
    sched-messaging:(401) |   2990.699 ms |    38705 | avg:   0.661 ms | max:  67.046 ms | max start: 456532.624830 s | max end: 456532.691876 s
    qemu-system-x86:(7)   |    179.764 ms |     2191 | avg:   0.152 ms | max:  21.857 ms | max start: 456532.576434 s | max end: 456532.598291 s
    sshd:48125            |      0.522 ms |        2 | avg:   0.037 ms | max:   0.046 ms | max start: 456532.514610 s | max end: 456532.514656 s
  <SNIP>
    ksoftirqd/11:82       |      0.063 ms |        1 | avg:   0.005 ms | max:   0.005 ms | max start: 456532.769366 s | max end: 456532.769371 s
    kworker/9:0-mm_:34624 |      0.233 ms |       20 | avg:   0.004 ms | max:   0.007 ms | max start: 456532.690804 s | max end: 456532.690812 s
    migration/13:93       |      0.000 ms |        1 | avg:   0.004 ms | max:   0.004 ms | max start: 456532.512669 s | max end: 456532.512674 s
   -----------------------------------------------------------------------------------------------------------------
    TOTAL:                |   3180.750 ms |    41368 |
   ---------------------------------------------------

  # echo $?
  0

  # perf sched map
    *A0                                                               456532.510141 secs A0 => migration/0:15
    *.                                                                456532.510171 secs .  => swapper:0
     .  *B0                                                           456532.510261 secs B0 => migration/1:21
     .  *.                                                            456532.510279 secs
  <SNIP>
     L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7 *L7  .   .   .   .    456532.785979 secs
     L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7 *L7  .   .   .    456532.786054 secs
     L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7 *L7  .   .    456532.786127 secs
     L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7 *L7  .    456532.786197 secs
     L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7  L7 *L7   456532.786270 secs
  # echo $?
  0

  # perf sched replay
  run measurement overhead: 108 nsecs
  sleep measurement overhead: 66473 nsecs
  the run test took 1000002 nsecs
  the sleep test took 1082686 nsecs
  nr_run_events:        49334
  nr_sleep_events:      50054
  nr_wakeup_events:     34701
  target-less wakeups:  165
  multi-target wakeups: 766
  task      0 (             swapper:         0), nr_events: 15419
  task      1 (             swapper:         1), nr_events: 1
  task      2 (             swapper:         2), nr_events: 1
  <SNIP>
  task    715 (     sched-messaging:    110248), nr_events: 1438
  task    716 (     sched-messaging:    110249), nr_events: 512
  task    717 (     sched-messaging:    110250), nr_events: 500
  task    718 (     sched-messaging:    110251), nr_events: 537
  task    719 (     sched-messaging:    110252), nr_events: 823
  ------------------------------------------------------------
  #1  : 1325.288, ravg: 1325.29, cpu: 7823.35 / 7823.35
  #2  : 1363.606, ravg: 1329.12, cpu: 7655.53 / 7806.56
  #3  : 1349.494, ravg: 1331.16, cpu: 7544.80 / 7780.39
  #4  : 1311.488, ravg: 1329.19, cpu: 7495.13 / 7751.86
  #5  : 1309.902, ravg: 1327.26, cpu: 7266.65 / 7703.34
  #6  : 1309.535, ravg: 1325.49, cpu: 7843.86 / 7717.39
  #7  : 1316.482, ravg: 1324.59, cpu: 7854.41 / 7731.09
  #8  : 1366.604, ravg: 1328.79, cpu: 7955.81 / 7753.57
  #9  : 1326.286, ravg: 1328.54, cpu: 7466.86 / 7724.90
  #10 : 1356.653, ravg: 1331.35, cpu: 7566.60 / 7709.07
  # echo $?
  0

Signed-off-by: Yang Jihong <[email protected]>
Signed-off-by: Namhyung Kim <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string")
Signed-off-by: Sasha Levin <[email protected]>
maxdog988 pushed a commit that referenced this pull request Nov 5, 2024
[ Upstream commit a848c29 ]

On the node of an NFS client, some files saved in the mountpoint of the
NFS server were copied to another location of the same NFS server.
Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference
crash with the following syslog:

[232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116
[232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116
[232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058
[232066.588586] Mem abort info:
[232066.588701]   ESR = 0x0000000096000007
[232066.588862]   EC = 0x25: DABT (current EL), IL = 32 bits
[232066.589084]   SET = 0, FnV = 0
[232066.589216]   EA = 0, S1PTW = 0
[232066.589340]   FSC = 0x07: level 3 translation fault
[232066.589559] Data abort info:
[232066.589683]   ISV = 0, ISS = 0x00000007
[232066.589842]   CM = 0, WnR = 0
[232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400
[232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000
[232066.590757] Internal error: Oops: 96000007 [#1] SMP
[232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2
[232066.591052]  vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs
[232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1
[232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06
[232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4]
[232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4]
[232066.598595] sp : ffff8000f568fc70
[232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000
[232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001
[232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050
[232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000
[232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000
[232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6
[232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828
[232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a
[232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058
[232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000
[232066.601636] Call trace:
[232066.601749]  nfs4_reclaim_open_state+0x220/0x800 [nfsv4]
[232066.601998]  nfs4_do_reclaim+0x1b8/0x28c [nfsv4]
[232066.602218]  nfs4_state_manager+0x928/0x10f0 [nfsv4]
[232066.602455]  nfs4_run_state_manager+0x78/0x1b0 [nfsv4]
[232066.602690]  kthread+0x110/0x114
[232066.602830]  ret_from_fork+0x10/0x20
[232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00)
[232066.603284] SMP: stopping secondary CPUs
[232066.606936] Starting crashdump kernel...
[232066.607146] Bye!

Analysing the vmcore, we know that nfs4_copy_state listed by destination
nfs_server->ss_copies was added by the field copies in handle_async_copy(),
and we found a waiting copy process with the stack as:
PID: 3511963  TASK: ffff710028b47e00  CPU: 0   COMMAND: "cp"
 #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4
 #1 [ffff8001116ef760] __schedule at ffff800008dd0650
 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00
 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0
 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c
 #5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898
 #6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4]
 #7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4]
 #8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4]
 #9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4]

The NULL-pointer dereference was due to nfs42_complete_copies() listed
the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state.
So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and
the data accessed through this pointer was also incorrect. Generally,
the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or
open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state().
When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED
and copies are not deleted in nfs_server->ss_copies, the source state
may be passed to the nfs42_complete_copies() process earlier, resulting
in this crash scene finally. To solve this issue, we add a list_head
nfs_server->ss_src_copies for a server-to-server copy specially.

Fixes: 0e65a32 ("NFS: handle source server reboot")
Signed-off-by: Yanjun Zhang <[email protected]>
Reviewed-by: Trond Myklebust <[email protected]>
Signed-off-by: Anna Schumaker <[email protected]>
Signed-off-by: Sasha Levin <[email protected]>
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Labels
None yet
Projects
None yet
Development

Successfully merging this pull request may close these issues.

4 participants