Update to v1.2.1

Drivers/BSP/PY32F002Bxx_Start_Kit/py32f002bxx_Start_Kit.c

@@ -216,7 +216,11 @@ void BSP_PB_DeInit(Button_TypeDef Button)
   */
 uint32_t BSP_PB_GetState(Button_TypeDef Button)
 {
+#if StartKitVersion == 2
+  return (HAL_GPIO_ReadPin(BUTTON_PORT[Button], BUTTON_PIN[Button]) == GPIO_PIN_RESET);
+#else
   return HAL_GPIO_ReadPin(BUTTON_PORT[Button], BUTTON_PIN[Button]);
+#endif
 }
 
 #ifdef HAL_UART_MODULE_ENABLED
@@ -327,6 +331,180 @@ int __io_putchar(int ch)
   return ch;
 }
 
+int _write(int file, char *ptr, int len)
+{
+  int DataIdx;
+  for (DataIdx=0;DataIdx<len;DataIdx++)
+  {
+    __io_putchar(*ptr++);
+  }
+  return len;
+}
+#endif
+#else
+static uint32_t ReloadD = 0;
+static uint32_t MinD = 0;
+
+/**
+  * @brief  GPIO Config As USART
+  * @param  None
+  * @retval None
+  */
+void BSP_USART_Config(void)
+{
+  GPIO_InitTypeDef  GPIO_InitStruct = {0};
+
+  DEBUG_USART_TX_GPIO_CLK_ENABLE();
+
+  GPIO_InitStruct.Pin = DEBUG_USART_TX_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;            /* Push-pull output */
+  GPIO_InitStruct.Pull = GPIO_PULLUP;                    /* Enable pull-up */
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;     /* GPIO speed */  
+  /* GPIO Initialization */
+  HAL_GPIO_Init(DEBUG_USART_TX_GPIO_PORT, &GPIO_InitStruct);   
+  HAL_GPIO_WritePin(GPIOB,GPIO_PIN_4,GPIO_PIN_SET);
+  ReloadD = SysTick->LOAD;
+  MinD = (ReloadD+1)*10/96;
+}
+
+/**
+  * @brief  writes a character to the usart
+  * @param  SystickStart
+  * @param  ReloadData  
+  * @param  MinData
+  * @retval NULL
+  */
+static void BSP_Delay(uint32_t SystickStart,uint32_t ReloadData, uint32_t MinData)
+{
+   uint32_t SystickCurrent = 0;
+   while(1)
+   {     
+     SystickCurrent = SysTick->VAL;
+
+     if(SystickCurrent < SystickStart)
+     {
+       if((SystickStart-SystickCurrent) >= MinData)
+       {
+         break;
+       }
+     }
+     else
+     {
+       if(SystickCurrent <= (ReloadData+1 - MinData + SystickStart))
+       {
+         break;
+       }
+     }
+   }
+}
+
+/**
+  * @brief  writes a character to the usart
+  * @param  ch
+  *         *f
+  * @retval the character
+  */
+static void BSP_TransmitChar(uint8_t ch)
+{
+  uint8_t temp = 0;
+  uint32_t SystickStart = SysTick->VAL ;
+
+  for(uint8_t i=0;i<10;i++)
+  {
+    if(i==0)
+    {
+      HAL_GPIO_WritePin(DEBUG_USART_TX_GPIO_PORT,DEBUG_USART_TX_PIN,GPIO_PIN_RESET);
+    }
+    else if(i == 9)
+    { 
+      BSP_Delay(SystickStart, ReloadD, MinD);
+
+      HAL_GPIO_WritePin(DEBUG_USART_TX_GPIO_PORT,DEBUG_USART_TX_PIN,GPIO_PIN_SET);
+
+      if(SystickStart >= MinD)
+      {
+        SystickStart = SystickStart - MinD;
+      }
+      else
+      {
+        SystickStart = ReloadD + 1 + SystickStart - MinD;
+      }
+      BSP_Delay(SystickStart, ReloadD, MinD);
+    }
+    else
+    {
+      temp=ch&0x01;
+      BSP_Delay(SystickStart, ReloadD, MinD); 
+      switch(temp)
+      {
+        case 1: 
+        {
+          HAL_GPIO_WritePin(DEBUG_USART_TX_GPIO_PORT,DEBUG_USART_TX_PIN,GPIO_PIN_SET);
+          break;
+        }
+        case 0:
+        {
+          HAL_GPIO_WritePin(DEBUG_USART_TX_GPIO_PORT,DEBUG_USART_TX_PIN,GPIO_PIN_RESET);
+          break;
+        }
+
+        default: break;
+      }
+      ch>>=1;
+      if(SystickStart > MinD)
+      {
+        SystickStart = SystickStart - MinD;
+      }
+      else
+      {
+        SystickStart = ReloadD + 1 + SystickStart - MinD;
+      }
+    }
+  }
+}
+
+#if (defined (__CC_ARM)) || (defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050))
+/**
+  * @brief  writes a character to the usart
+  * @param  ch
+  *         *f
+  * @retval the character
+  */
+int fputc(int ch, FILE *f)
+{
+  BSP_TransmitChar(ch);
+  return (ch);
+}
+
+
+#elif defined(__ICCARM__)
+/**
+  * @brief  writes a character to the usart
+  * @param  ch
+  *         *f
+  * @retval the character
+  */
+int putchar(int ch)
+{
+  /* Send a byte to USART */
+  BSP_TransmitChar(ch);
+
+  return (ch);
+}
+#elif  defined(__GNUC__)
+/**
+  * @brief  writes a character to the usart
+  * @param  ch
+  * @retval the character
+  */
+int __io_putchar(int ch)
+{
+  /* Send a byte to USART */
+  BSP_TransmitChar(ch);
+
+  return ch;
+}
+
 int _write(int file, char *ptr, int len)
 {
   int DataIdx;

Drivers/BSP/PY32F002Bxx_Start_Kit/py32f002bxx_Start_Kit.h

@@ -72,6 +72,9 @@ typedef enum
   BUTTON_MODE_EXTI = 1
 } ButtonMode_TypeDef;
 
+#define StartKitVersion 2
+/* #define StartKitVersion 1 */
+
 #define LEDn                               1
 
 #define LED3_PIN                           GPIO_PIN_1
@@ -137,6 +140,12 @@ typedef enum
 
 #define DEBUG_USART_IRQHandler                  USART1_IRQHandler
 #define DEBUG_USART_IRQ                         USART1_IRQn
+
+#else
+
+#define DEBUG_USART_TX_GPIO_PORT                GPIOB
+#define DEBUG_USART_TX_GPIO_CLK_ENABLE()        __HAL_RCC_GPIOB_CLK_ENABLE()
+#define DEBUG_USART_TX_PIN                      GPIO_PIN_4
 #endif
 /************************************************************/