AWIVE Configurator

The AWIVE configurator is a software used to analyze images in order to determine the configuration used for the awive project.

Getting Started

Prerequisites

This software was tested in:

• Linux host computer (ubuntu 22.04)
• Python 3.11.2

Installation

If you are using uv, execute the commands below:

uv sync
source .venv/bin/activate

Otherwise, excute these commands:

python -m venv venv
source venv/bin/activate
python -m pip install .

Usage

The awive configurator have the following features:

• image analyzer
• AWIVE runner

Before attempting to use any feature, crete your own configuration file:

cp config.example.json config.json

Image Analyzer

In order run the image analyzer, you require the following:

• The path of the video to be analyzed
• The path where to save frames extracted from the video

Firstly, set both previous paths in the config.json in the keys dataset.video_path and dataset.image_dataset respectively.

Then, execute the command below to just visualize a frame from the video:

python -m awivec.analyze_image config.json -P

It should display some image like the one shown below:

Probably the displayed image is not suitable for any of AWIVE velocimetry algorithms. Thus, the following steps must be done in order to calibrate the parameters of the config.json file:

1. Orthorectification
2. Pre-Region of Interest
3. Image rotation
4. Region of Interest
5. Image Correction

1. Orthorectification

Orthorectification pre-processing is necessary when the images in the video are distorted due to the camera's position. This occurs when the camera recording the video was not placed directly in front of the river.

To calibreate the orthorectification parameters there are required four ground-control-points (GCPs).

Visualize the image:

python -m awivec.analyze_image config.json -P

Identify the 4 GPCs and save them in the config.json file. The keys are dataset.gcp.pixels. The order of the GCPs in the list must be in clockwise order starting from the top-left corner.

Determine the coordinates of the GCPs in the real world and save them in the config.json file. The keys are dataset.gcp.meters. The order of the coordinates in the list must be the same as the order of the GCPs in the dataset.gcp.pixels key.

If you only have the distances between the GCPs, you can use the awivec.from_distances script:

python -m awivec.from_distances

Then enable gcp by setting True in the dataset.gcp.enable.

Finally, run the command below to visualize the orthorectified image:

python -m awivec.analyze_image config.json -P -u

2. Pre-Region of Interest

To avoid processing unnecessary information, it is recommended to define a pre-region of interest. This region is used to crop the image before applying the AWIVE velocimetry algorithms.

3. Image rotation

Modify preprocessing.rotate key in the config.json file to adjust the rotation of the image until the river flow goes from left to right.

Use this command to show river flow:

python -m awivec.video config.json -u -r -z

4. Region of Interest

5. Image Correction

Then, checkout how the image looks with the awive pre-processing, perhaps the default configuration might generate an unusable image. Edit the keys of preprocessing in the config.json file.

python -m awivec.analyze_image config.json -P -u -r

As a suggestion, begin by calibrating the processing.pre_roi to define only the area of interest. Next, use preprocessing.rotate_image to adjust until the direction of the river aligns with 0 degrees, making it a horizontal line. Finally, modify the preprocessing.roi key to encompass only the water in the image.

AWIVE Runner

When the config.json file is ready, run the command below:

python -m awivec.run_awive config.json -v

Then, a video like the one shown below should be displayed.

Considerations:

• the river must be flowing to the left, that is in angle 180
• to find the coordinates, such as I only had the distances between the GCPs I had to use Geogebra to find out the coordinates in a cardinal plane. then I wrote those coordinates in the config.json and add offset to not use negative numbers but Actually I don't know if negative'll break the code or not.

GUI

docker compose up -d --build