This system uses a 3x3 Resistive Memory Array of potentiometers (in series with diodes) to replicate a crossbar array of memristors to encode a binary image into high and low resistance states, which can be used for image recognition. The connections involve: Raspberry Pi-to-Display, which can be achieved via Ethernet cable to connect to a laptop screen, or an HDMI cable to a screen accepting HDMI input; USB Connection between Raspberry Pi and Arduino; MicroUSB power supply connection to the Raspberry Pi; various connections to get the PWM-to-DAC board connected to the crossbar array for stabilized voltage outputs.
- ELEGOO UNO R3 - Arduino-based microcontroller
- LTC2645 Demo Board - PWM-to-DAC converter
- 9V Battery - External Power Supply
- Fan Blade and Motor - Application of Image Recognition
- 100k Ohms Potentiometers (9) - Manually programmable resistors
- Yellow-Green LEDs (9) - LEDs (diodes) for current control
- 1k Ohms Resistors (3) - Reference resistors for measuring voltage and current through at the bottom of each column
- Raspberry Pi 3B - Mini-computer used for image capture and processing
- Arducam 5MP Camera (X000VGJ8BL) - Camera Module connected to Pi for capturing images
- Various cables and wires - Used to make connections within the system
- Laptop/HDMI Input Screen - Used to display Raspberry Pi screen
- Arduino IDE - Coding software for Arduino-based microcontrollers
- Python - All purpose coding software used to connect image capture and processing
- Visual Studio Code - Text editor that's useful for convenient coding
Analog and Digital Pins:
- A0, A1, A2 for reading voltage drops over reference resistor in the three columns
- Digital 5, 6, 9 for PWM outputs to the IN A, B, C inputs of the PWM-to-DAC board, which connects VOUT A, B, C to the three rows
- Digital 10, 11, 12 for outputs to the IC controlling the motor supplied by an external power supply
Main loop:
- Checks for serial input with binary code
- Formats binary code into a 3x3 array to determine which voltages should be applied to which cells
- Computes all the average currents through each cell, and then sums the columns and checks if they are all within the correct range for a match
- The decided values were LRS-17.3k Ohms-2.22V and HRS-100k Ohms-4.71V, and the column current match range was 54uA-78uA
- Reference resistor at the bottom of each column - 1k Ohms so that it would have little influence on the overall current
- If there was a match, the motor would turn on and the fan would spin counterclockwise Otherwise, the motor would be off
- Imports and Installations: Download Python, then type these commands in the command prompt:
pip install opencv-contrib-python
pip install pyserial
pip install Pillow
pip install numpy
pip install picameraNOTE: Everything should be installed properly on the Raspberry Pi's SD Card, but to do it all over again, the keyword "sudo" must be placed in front of all the installation commands to work on the Pi's OS
- Image Capture: Using the Raspberry Pi, use PiCamera to capture the image Using laptop webcam, use OpenCV camera to capture the image
- Image Processing: Perform a binary threshold conversion to make the image black & white, then process it into the binary code necessary to be sent to the Arduino
- Serial Communication: Use pySerial's Serial object to open up a COM port connection, and then write the necessary values over to the Arduino Once the Arduino does all the current calculations, it sends it all back to python serially to be displayed to the user When the code ends, the serial port is closed
The system worked very well, being fully accurate except in a few cases where there were minor hardware disruptions leading to incorrect current readings for specific cells. It would be cool to see this system replicated onto an actual memristor chip so that it could take input images and automatically encode them into memory, and then use that memory to follow up and compare other images and see if there's a match.