Add support for MAX17616

doc/sphinx/source/drivers/power/max17616.rst

@@ -0,0 +1 @@
+.. include:: ../../../../../drivers/power/max17616/README.rst

doc/sphinx/source/projects/power/max17616.rst

@@ -0,0 +1 @@
+.. include:: ../../../../../projects/max17616/README.rst

drivers/power/max17616/README.rst

@@ -0,0 +1,206 @@
+MAX17616 no-OS driver
+=====================
+
+.. no-os-doxygen::
+
+Supported Devices
+-----------------
+
+* `MAX17616/MAX17616A <https://www.analog.com/MAX17616>`_
+
+Overview
+--------
+
+The MAX17616/MAX17616A offers highly versatile and programmable protection
+boundaries for systems against input voltage faults and output overcurrent
+faults. Input-voltage faults (with positive polarity) are protected up to +80V
+(without Reverse Current Protection)/+75V (with Reverse Current Protection), by
+an internal nFET featuring low ON-resistance (20mΩ typ). The devices feature a
+programmable undervoltage-lockout (UVLO) thresholds by using external voltage-
+dividers. The MAX17616 features a programmable overvoltage-lockout (OVLO) while
+MAX17616A offers a programmable output voltage clamp function through the OVFB
+pin that features an output voltage limiting regulation during input transient
+surge events. Input undervoltage and overvoltage protection (MAX17616)/output
+voltage clamp function (MAX17616A) can be programmed across the entire 3V to 80V
+operating range.
+
+Applications
+------------
+
+MAX17616
+--------
+
+* Input Voltage and Output Overcurrent Protections
+* Loss of Ground Protection
+* Surge Protection
+
+MAX17616 Device Configuration
+-----------------------------
+
+Driver Initialization
+---------------------
+
+In order to be able to use the device, you will have to provide the support
+for the communication protocol (I2C) alongside other GPIO pins if needed in the
+specific application (depends on the way the device is used).
+
+The first API to be called is **max17616_init**. Make sure that it return 0,
+which means that the driver was initialized correctly.
+
+The initialization API uses the device descriptor and an initialization
+parameter.
+
+Status Bytes
+------------
+
+Assertion in the status bytes/words indicates fault/warning in device input/
+output, temperature, and communication, memory and logic. These statuses can be
+accessed via the **max17616_read_status** API.
+
+Telemetry
+---------
+
+Measurements for each output channel can be read using the
+**max17616_read_telemetry_all** API. Some telemetry values includes input/output
+voltage, input current, temperature, and output power.
+
+MAX17616 Driver Initialization Example
+--------------------------------------
+
+.. code-block:: bash
+
+	struct max17616_dev *max17616_dev;
+
+	struct no_os_i2c_init_param i2c_ip = {
+		.device_id = I2C_DEVICE_ID,
+		.max_speed_hz = I2C_CLK_SPEED,
+		.platform_ops = I2C_OPS,
+		.slave_address = I2C_ADDR,
+		.extra = I2C_EXTRA,
+	};
+
+	struct max17616_init_param max17616_ip = {
+		.i2c_init = &i2c_ip,
+		.chip_id = ID_MAX17616,
+	};
+
+	ret = max17616_init(&max17616_dev, &max17616_ip);
+	if (ret)
+		goto error;
+
+MAX17616 no-OS IIO support
+--------------------------
+
+The MAX17616 IIO driver comes on top of the MAX17616 driver and offers support
+for interfacing IIO clients through libiio.
+
+MAX17616 IIO Device Configuration
+---------------------------------
+
+Channels
+--------
+
+The device has a total of 15 input channels and 7 output channels:
+
+**Telemetry Input Channels:**
+
+* ``vin - input voltage``
+* ``vout - output voltage``
+* ``iout - output current``
+* ``temp1 - device temperature``
+* ``pout - output power (calculated from vout * iout)``
+
+**Status Input Channels:**
+
+* ``status_word - 16-bit comprehensive status register (hex)``
+* ``status_vout - VOUT status byte (hex)``
+* ``status_iout - IOUT status byte (hex)``
+* ``status_input - INPUT status byte (hex)``
+* ``status_temperature - TEMPERATURE status byte (hex)``
+* ``status_cml - Communication/Memory/Logic status byte (hex)``
+* ``status_mfr_specific - Manufacturer-specific status byte (hex)``
+* ``capability - Device capability register (hex)``
+
+**Control Output Channels:**
+
+* ``operation - device operation state (0=disabled, 1=enabled)``
+* ``clmode - current limit mode setting``
+* ``istart_ratio - current start ratio setting``
+* ``tstoc - short circuit timeout setting``
+* ``istlim - current limit setting``
+* ``vout_uv_fault_limit - output undervoltage fault limit setting``
+
+Input Channel Attributes
+------------------------
+
+The telemetry input channels (vin, vout, iout, temp1, pout) each have 2 channel
+attributes:
+
+* ``raw - the raw converted value from the device using DIRECT format conversion``
+* ``scale - the scale factor (always returns 1 for DIRECT format values)``
+
+The status input channels (status_word, status_vout, status_iout, status_input,
+status_temperature, status_cml, status_mfr_specific, capability) each have
+1 channel attribute:
+
+* ``raw - the raw hexadecimal value of the status register``
+
+Output Channel Attributes
+-------------------------
+
+The control output channels (operation, clmode, istart_ratio, tstoc, istlim,
+vout_uv_fault_limit) each have 1 channel attribute:
+
+* ``raw - read/write the integer value of the control setting``
+
+Global Attributes
+-----------------
+
+The device has a total of 4 global attributes:
+
+* ``operation - device operation state (read/write: "enabled"/"disabled" or "1"/"0")``
+* ``clear_faults - clears all asserted faults (write-only, write any value to trigger)``
+* ``device_info - device identification information (read-only string)``
+* ``fault_summary - summary of current active faults (read-only string)``
+
+Debug Attributes
+----------------
+
+The device has no debug attributes implemented.
+
+MAX17616 IIO Driver Initialization Example
+------------------------------------------
+
+.. code-block:: bash
+
+	int ret;
+
+	struct max17616_iio_desc *max17616_iio_desc;
+	struct max17616_iio_desc_init_param max17616_iio_ip = {
+		.max17616_init_param = &max17616_ip,
+	};
+
+	struct iio_app_desc *app;
+	struct iio_app_init_param app_init_param = { 0 };
+
+	ret = max17616_iio_init(&max17616_iio_desc, &max17616_iio_ip);
+	if (ret)
+		return ret;
+
+	struct iio_app_device iio_devices[] = {
+		{
+			.name = "max17616",
+			.dev = max17616_iio_desc,
+			.dev_descriptor = max17616_iio_desc->iio_dev,
+		}
+	};
+
+	app_init_param.devices = iio_devices;
+	app_init_param.nb_devices = NO_OS_ARRAY_SIZE(iio_devices);
+	app_init_param.uart_init_params = uart_ip;
+
+	ret = iio_app_init(&app, app_init_param);
+	if (ret)
+		return ret;
+
+	return iio_app_run(app);